Cars Chalenge Motorcycle

Hey whats goin on guys, i just bought a 97 2.8 quattro 5 speed. I love the thing, its got a lowered german racing suspension, short throw, intake, deleted res with true dual delta flow 44 and the most amazing momo racing seats. I had a 95 accord before this but i killed it racing. ive been into cars for a while, my accord had 300 hpw before i killed it which is pretty good considering everything was done by me. It had i/e/h, short throw, bored tb, h22 head swap, f23 intake man, centerforce clutch, and Jspec tuned Ecu. My audi is slower but i like it a lot, im looking at getting a tap chip, and eventually boost it. I have some crazy ideas about doing a twin turbo, with the way the V engine is facing it would be perfect minus the weak internals. Its got a strong head but weak bottom, if i swaped the S4 bottom it could work, I think. But thats just a fantasy for now. Me and my cousin are hopefully gonna open a performance shop with in the next couple months and we are both gonna take out loans for the business and our cars. We figure that way if the shop doesnt go over well and we fail atleast we got fast cars.

It was time to replace the brake rotors on my Audi A6 that were wearing thin after 90,000 km. Instead of replacing with OEM rotors, I decided to replace with OEM sized two piece rotors. I also opted to continue with the EBC Red Stuff pads which had served me well when I replaced the OEM brake pads at 50,000 km.

Review of the EBC Red Stuff brake pads.
OEM brake pads lasted for 50,000 km for the first time and the EBC Red Stuff brake pads which I swapped to lasted 40,000 km before I changed it along with the rotors. At both instances, I had both the front and rear sets changed at the same time. The brake oil was replaced at the 50,000 km change but this time, they did not appear to need a change and so I did not.

I chose to swap the EBC Red Stuff pads primarily because I was mainly looking for a small increase in braking performance, and a huge reduction in brake dust. And the EBC pads did all that. Braking was sharper compared to the OEM pads which were quite inadequate for emergency braking. Braking on the OEM pads felt vague and you never got the feeling that you would stop in time when you needed to as the Audi A6 is a heavy car. As a result, I tended to brake early, just in case. The dust from the OEM pads was quick to appear as well. The swap to the EBC pads was just what I was looking for. Naturally, one cannot expect a change of brake pads to instantly produce massive stopping power. And I was not looking for that. Braking was improved slightly, and it was enough to be noticeable. And the brake dust was gone, thanks to the ceramic compound on the EBC pads. Sure, if you looked hard enough, there is still a coating of brake dust on the rims, albeit a light coloured layer.

On the surface, it would appear that the EBC pads had a shorter lifespan - 10,000 km less than the OEM pads. In fact, it is hard to make a comparison as I was driving harder on the EBC pads. In the first 50,000 km, I was mostly doing short trips within the city and at most a 150 km run to Zhuhai or a 120 km run to Guangzhou. All of which was on flat ground and decent roads. After I made the change to the EBC pads, I had made a total of 6 long trips that were between 1200 km to 1500 km each way round and along the way there were long mountainous stretches with long stretches of downhill runs where opportunities to use the brakes were plentiful. In addition, I had also started to drive the car harder.

In all, I was very satisfied with the EBC Red Stuff brake pads.

Replacement Two Piece Rotors
In a luxurious sedan like the Audi A6, you cannot and should not turn it into a sports car. What you can do is to make small improvements so that it becomes a little more fun to drive. My modifications have centred around improving the handling of the car slightly with small adjustments. Even then, I have mostly adhered to the principle of replacing OEM parts with lighter and stronger aftermarket parts as the time for replacement comes. With the brake rotors wearing thin, it also presented me with an opportunity to swap the OEM rotors with something lighter. Swapping out for lighter rotors reduces unsprung weight. A reduction in unsprung weight theoretically leads to lighter load on the suspension and this translates to better suspension response and subsquently, better ride comfort and ability to soak up the irregularities on the road surface. In addition, the loss in unsprung weight also reduces the moment of inertia which means less energy is required to get moving. And in theory, this leads to faster acceleration and throttle response. In practice, the weight reduction from taking a kilogramme off each corner could well be meaningless, or virtually impossible to detect. Experts or enthusiasts tell me that I would expect to see greater improvement if I were to swap rims and tyres for lighter versions since the weight loss at each corner would be more like 3-4 kg or more. I couldnt agree more. However, it is not the time to replace the rims or the tyres and it is the time, however, to have the rotors changed. As such, I chose to go ahead and replace the OEM rotors with lighter aftermarket ones anyway. And even if it did not produce a noticeable effect, when the time comes to change the rims and tyres, I believe the effect certainly would be very noticeable when the aftermarket rotors were paired with lighter rims and wheels.

This is the front rotor and I have also opted for a slotted rotor since it looked nice and sporty too. I do not expect to need the slots to help counter brake fade since even with the hardest driving I have done so far, I have not had any problems with brake fade. The hub is aluminium alloy and lifting it and comparing it with the OEM rotors, the weight difference was obvious. Unfortunately, I did not have a scale on hand to measure the weights but I would put it as about 1-1.5 kg weight savings.

Download More Pictures Here.

Currently the MINI plant in Oxford, England is running at full capacity, so it will not be possible for BMW to build another version at that plant. Magna on the other hand has extra capacity at its Graz, Austria plant where the Chrysler 300 was built until recently when Chrysler decided to move the production to its Brampton, Ontario plant. Also the next BMW X3 will not be built at the Magna plant as it is switching to BMWs South Carolina plant. The Magna plant built 26,400 Chrysler 300s and 113,000 X3s last year. The company is trying to work with BMW to build 65,000 MINI Colorados to make up for the loss of the X3 and 300 sedan.

Hot Girls vs Sexy Motor Sport Babes

Called the DUU Concept, the naked ride is a aggregate of "a adventurous European rolling anatomy powered by a able-bodied American big-twin." The agent is a 1.9-liter (117 cu. in.) X-Wedge supplied by S&S. Wrapped about that powerplant is a anatomy that CR&S says can be tailored by the chump – although they dont announce how above presenting the best of distinct or two-seater versions.

Speaking about the cultures of moto-structure of compounds in this motorcycle, implying the existence of a European sports chassis and a large, traditionally-unit type of the American V-Twin. The engine will have a capacity 1.926ss, but data on the power and weight of the motorcycle is not yet known. Design DUU swift and aggressive, though, unwittingly, an association with Ducati Streetfighter, if that was designed Harley-Davidson, with the use of design elements from musclebike Yamaha VMax and MT-01.